Purpose of this blog

Dmitry Yudo aka Overlord, jack of all trades
David Lister aka Listy, Freelancer and Volunteer

Wednesday, September 3, 2014

[WoTB] Draft Specs for Android


While we are getting ready for WoT Blitz testing on Android, below are draft specs to launch the game on devices that run Google's operating system:

  • OS: Android 4.0+
  • GPU: Mali-400MP, Adreno 320, PoweVR SGX544, Tegra 3 or better
  • CPU: 2-core @ 1200 MHz or better
  • RAM: 1GB or better

Especially at this early stage meeting the minimum requirements doesn't guarantee smooth play. So the more powerful your device, the better.

Sunday, August 31, 2014

Unconquerable!

Sorry to say, today I'll be talking a bit about World of Tanks, I know some of you might be put off by this, but bear with me. There's plenty of history and new research! All this comes from documents held at the national archives at Kew.
 As you know World of Tanks is transferring to HD at the moment, and with that the tank's armour gets reviewed and brought as close as possible to its historical level. Well at the moment the FV214 Conqueror is undergoing its HD treatment, and so we were tasked with looking for armour values. Some of you might already be reaching for Google, muttering about having already seen an armour profile for the Conqueror, well yes and no. There are plenty of guesses about the Conquerors armour level, but nothing exact. Equally there's some evidence to suggest that the turret casting isn't a uniform thickness, with the armour basis (The LOS thickness) being constant, but the actual thickness being varied depending on the slope.
A naked Conqueror turret
Of course the usual answer is to dispatch someone to spend a fun day crawling all over a Conqueror with a thickness gauge and measure the armour. Here's where it gets interesting. Wargaming has tried at least three (maybe more) times to measure the Conqueror's front turret. Each time it was a different person, on a different Conqueror with a different thickness gauge. These are not people who are new to the job either. Each time they've not been able to get a reading. Something in the way the turret is cast has been preventing an accurate measurement being taken.

That's where I came in, Although I do have a local Conqueror, I've not got a thickness gauge or any experience of using it, so the likelihood of me being successful is nil, but what I could do was start combing archives for a primary source answer. I did find some interesting stuff but no armour value. Again the mystery deepens. There isn't a given value. Even on documents that list all the other armour thickness, the frontal turret thickness isn't given, just the level of protection it is required to give.

But first, lets talk about the Conqueror's early life. In the late 40's the British opinion was that armour had the upper hand in the armour vs gun battle, and looking at Soviet tanks of the time they were concerned about tank armament. The British were facing a dilemma. On one hand they needed a weapon with a high enough rate of fire to "suppress" enemy positions during an attack, this of course was entirely suited to guns such as the 20 pounder or the US 90mm. But both those guns were deemed inadequate against the latest Soviet armour. The answer was obvious, looking back at the Second World War they could see a system that had worked, the Sherman Firefly and 75mm armed Sherman's that had made up a large chunk of the British armoured force.
So the plan was formed to give Centurion regiments a 120mm armed Centurion. Initial trials resulted in the FV4004 Conway, and it was foreseen that over time the tank could be developed into something with a lower turret.
As an aside, its curious to note that despite the perceived issues in 1948 the British were looking at developing a new infantry tank with utterly ridiculous armour (400mm-350mm) and only a 77mm gun.
Now I need to quickly explain the way the British armour organisation was seen in this period. Armoured regiments were seen as mobile striking units, used for the attack. RAC regiments were viewed as defensive in nature.
The Conqueror was to be grouped into RAC regiments, with Cromwell's as command tanks, and armoured regiments would be equipped with Centurions with 20 pounders and FV4004 Conway's. However the Conqueror production and development went a lot faster than had been foreseen, and therefore the plan changed to one squadron in each RAC regiment and one troop in each armoured squadron would be converted into Conquerors. This resulted in a total requirement of 250 tanks needed.
Right from the start the Conqueror came under fire. First was the army in 1949 complaining about the protection levels and the poor ballistic shape of the Conqueror's turret. One proposal was to remove the gunner to improve the shape of the turret but this was thrown out for two reasons, first of all two man turrets were a bad idea. Secondly it would remove one of the Conqueror's big advantages, it was one of, if not the first tank to have hunter/killer ability. If you don't know what that is I'll explain. While the tank's gunner is engaging an enemy tank, the commander is free to look about and select a follow on target, as soon as the gunner has finished with his target he can instantly and effortlessly switch to the target the commander has highlighted. This allows for a much faster and rapid engagement of targets.

Note the direction the Commanders cupola is facing.
The next attack was the other services whom started complaining about the cost of the Conqueror program, and it took the defence Minister's personal intervention after a meeting with the army to lay that issue to rest.

But back to the armour values. The first big surprise was a 14mm Burster plate attached to the hull. This stand off armour was for the role of detonating HEAT and HESH warheads away from the hull. Some of you might ask why you've never heard of this before? Simply because it wasn't fitted in peacetime but was held as a theatre reserve to be deployed in the time of war. The other obvious question is how would that effect gun depression over the front hull? One suggestion was to shave 10mm of armour off the front slope to improve the depression, but that was never implemented. On the Conqueror although the gun could depress to -7.5 degrees, beyond -5.5 degrees a limiter kicked in that prevented the gun from being laid or used. This was in place because the Conqueror had a nasty habit of sticking its gun barrel into the ground. This was caused by the huge length of the L1 120mm barrel, which swung about a lot preventing it from firing on the move. See this video for an example, notice how much the gun barrel bounces around:
 
(video should start at 20 seconds in, if not that's where you want to be)

But what of the turret armour, the thing that set me off on the trip. Well the requirement was to be immune from the Soviet 100mm gun at point blank range through an arc of 60 degrees (30 degrees either side of the gun barrel). However after testing the best that could be achieved with the turret was that level of protection through half the required arc. This does allow us the ability to make a guess on the required thickness, as the documents helpfully included a table of Soviet gun performance.

But the issue remained that the turret wasn't very well armoured. That's when I hit gold. There was a proposal for a new better shaped turret, with drawing!
The gunner has been moved to the enlarged cupola, so the gunner and the commander are side by side. You'll note that the cupola is actually very well protected with a steeply sloped chunk of armour. The armour thicknesses are also given. Frontal protection is 13.5" with the sides offering 7" of protection.

And to close off, here's some follow on data on the Conqueror, that's just to help you to form a picture of the technical abilities of a Conqueror.
Turret traverse speeds were measured and found to be between 22-24 seconds for 360 degrees. Maximum elevation of the gun was 15 degrees. Reloading the gun took seven seconds and the road speed was 21.3 mph.